- Español
- Português
- русский
- Français
- 日本語
- Deutsch
- tiếng Việt
- Italiano
- Nederlands
- ภาษาไทย
- Polski
- 한국어
- Svenska
- magyar
- Malay
- বাংলা ভাষার
- Dansk
- Suomi
- हिन्दी
- Pilipino
- Türkçe
- Gaeilge
- العربية
- Indonesia
- Norsk
- تمل
- český
- ελληνικά
- український
- Javanese
- فارسی
- தமிழ்
- తెలుగు
- नेपाली
- Burmese
- български
- ລາວ
- Latine
- Қазақша
- Euskal
- Azərbaycan
- Slovenský jazyk
- Македонски
- Lietuvos
- Eesti Keel
- Română
- Slovenski
- मराठी
- Srpski језик
600A Elbow Connector Manufacturers
The 15kV Insulated Cap is the most recommended one in 600A elbow connector series, which is as an attachment to the charged casing accessories, to provide insulation for charged casing insulating sleeve, to provide dust-proof and moisture-proof envelope for uncharged joint. 600A insulation cap can be installed in 600A bush, bus-bar and hanging device. When the bus-bar and cable joint reserve have a spare line, must be sealed it with the 600A insulated cap.
The 15kV Hybrid Bus-bar in 600A elbow connector series, is also a good sales, which The test point can install live display to check the live status of the equipment and meet the requirements of the nuclear phase of the line. It can be operated with live, but cannot cut off short circuit current. It’s suitable for XLPE cable with sectional area 25mm2~150mm2. It can be used as load switch to switch off 200A current.
- View as
-
-
15kV Hybrid Bus-bar
600A bus-bar acts as bus-bar in the cable branch line. It can combine T cable joint, T -II cable joint, 600A extension tube and 600A insulation cap as a cable branch lines. 600A/ 200A hybrid bus-bar gathers 200A and 600A bolt type of bus-bar interface. The 15kV Hybrid Bus-bar is made of high quality EPDM. It has the characteristics of the insulation, fully sealed. With T type cable joint, T - type cable joint or elbow cable joint connection, configuration is varied.
Read MoreSend Inquiry
15kV Insulated Cap
The 15kV Insulated Cap is is as an attachment to the charged casing accessories, to provide insulation for charged casing insulating sleeve, to provide dust-proof and moisture-proof envelope for uncharged joint. 600A insulation cap can be installed in 600A bush, bus-bar and hanging device. When the bus-bar and cable joint reserve have a spare line, must be sealed it with the 600A insulated cap.
Read MoreSend Inquiry
15kV Bushing Extender
The 15kV Bushing Extender is mated with the conversion head to form a 600A/200A conversion head with extension bush, which can be installed directly on the 600A bus-bar or 600A bushings. The 200A jack can be installed with elbow surge arrester or elbow cable connector. The 15kV Bushing Extender is made of high quality EPDM (EPDM), fully insulated and sealed.
Read MoreSend Inquiry
15kV Integral Dead Break Bushing
600A/200A Integral Dead Break Bushing including The 15kV Integral Dead Break Bushing is used to convert a standard 600A dead break interface to a standard 200A load break integral.Used with a 200A insulated protective cap M.O.V Elbow Arrester. Grounding Elbow or Load Breaker Elbow Connector.A integral dead break bushing provides a fully shielded.It will be T-II connect if connects with T connect.
Read MoreSend Inquiry
15kV Type T Cable Connector
The 15kV Type T Cable Connector is fully insulated. Fully sealed. Used for high voltage underground cable connection equipment. Such as wind power substation, ring network cabinet and cable splicing box, the rated current is 600A, can be connected to the relevant specifications of the cable, cable type fault indicator can also be installed on the cable, can quickly and accurately find the fault point.
Read MoreSend Inquiry
